omv-zfs-ras-nas

Documentation of my openmediavault OpenZFS Raspberry Pi 4 Network-attached storage setup.

Why?

• I like OMV
• I want a system that I can run 24/7 with minimal power consumption.
• RAID is not supported by OMV when the hard disks are connected via USB. Technically using RAID with USB disks is possible but unreliable and dangerous.
• ZFS has some awesome features:
  • Supports (among other RAID-like modes) mirroring (replaces mdadm).
  • Supports snapshots.
  • Supports volumes (replaces LVM).
  • Supports encryption (replaces LUKS).
  • Supports compression.
  • ZFS can directly transfer snapshots to other machines, thus facilitating easy and fast off-site backup strategies.
  • Smart behavior when recovering from a failure (only syncs real data, not the entire drive).

Disclaimer

RAID is not a backup, it only protects you from a hard-drive failure. ZFS' support for snapshots adds some limited backup functionality. I still recommend a regular off-site backup.

Hardware

• Raspberry Pi 4 with 4GB RAM.
• A case with a fan.
  • Initially connected to 5V during compilation and testing of ZFS.
  • Afterwards connected to 3,3V to avoid noise.
• Two 2 TB laptop hard-drives selected for especially low energy consumption.
• An extra USB power supply with two USB ports to supply the hard-drives with enough power, especially during spin-up.
• The hard-drives are connected to the Raspberry Pi and the extra USB power supply using USB Y-cables and two cheap USB-SATA adapters.

Unsolved Problems:

The cheap USB-SATA adapters have a JSM (JMicron) Chipset which cannot properly handle some hdparm/smartctl commands. Configuring power management seems to work but querying whether the drive has spun down does not work. This currently prevents me from making the device spin down because it is woken up regularly for snapshots.

Reading material:

• Smartmontools USB Device Support
• Smartmontools USB Device Support (unsupported devices)

The chipset ASM1351 seems to support the required commands but I have not found a product that uses this chipset and meets my other requirements.

Benchmarks:

Sending a tar archive from a powerful machine to the ras-nas machine to store it on a ZFS filesystem:

ras-nas:~# nc -l 8888 > {dest on zfs}

nas:~# tar --acl -cpf - -C /srv/dev-disk-by-uuid-{uuid} . | pv -trabpte | nc -q0 ras-nas 8888
       342GiB 2:08:44 [45.4MiB/s] [45.4MiB/s]

Sending a snapshot from the ras-nas machine to a powerful machine:

nas:~# nc -l 8888 | zfs receive {dest zfs filesystem}

ras-nas:~# zfs send {source zfs filesystem} | pv -trabpte | nc -q0 nas 8888
           341GiB 1:08:36 [85.0MiB/s] [85.0MiB/s]

Reading Material

• OpenZFS - Building ZFS
• NAS-Server mit Raspberry Pi und OpenMediaVault einrichten (in german)
• Raspberry Pi 4: Minimalistisches NAS mit ZFS-Dateiverwaltung selbst bauen (behind paywall, in german)
• Introducing Raspberry Pi Imager, our new imaging utility
• 64-Bit-Version von Raspberry Pi OS (in german)
• NAS with ZFS on Raspberry Pi 4

Setup Steps

1. Install Raspberry Pi OS to microSD Card

Install the Raspberry Pi Imager software.

Install Raspberry Pi OS 64-bit images using the Raspberry Pi Imager (you have to download the image manually first).

The ZFS filesystem is intended to be run on 64-bit operating systems but also works on 32-bit systems, albeit with reduced performance.

Alternative: Install Raspberry Pi OS Lite (32-bit OS) to a microSD card.

2. Update your Raspberry Pi and your Raspberry Pi OS

To update the OS, run:

$ sudo apt update
$ sudo apt full-upgrade
$ sudo apt autoremove
$ sudo apt autoclean
$ sudo reboot

To see if updates for the EEPROM are available, run:

$ sudo rpi-eeprom-update

To actually perform an update of the EEPROM, run at your own risk:

$ sudo rpi-eeprom-update -a
$ sudo reboot

For further information read Raspberry Pi 4 boot EEPROM.

3. Configure Raspberry Pi OS

This step depends on your setup and your needs. For the goal of installing OMV and ZFS no special configuration steps are required.

To configure your Raspberry Pi OS run:

$ sudo raspi-config

Recommendations:

These are just my personal preferences:

• Enable SSH in raspi-config.
• Use ssh-copy-id to transfer your public SSH keys to the Raspberry Pi.
• Disable root login and password authentication in /etc/ssh/sshd_config.
• Install tmux for remote work on the Raspberry Pi.
• Enable mouse support in tmux:
  • Install gpm.
  • Add set -g mouse on to ~/.tmux.conf (you probably have to create it first).
• Install glances, and dstat for system performance measurements. Use pip (deb package not available)
• Disable swap:

sudo systemctl stop dphys-swapfile.service
sudo systemctl disable dphys-swapfile.service

4. Install OMV

Download the installer script:

wget -O install-omv.sh https://github.com/OpenMediaVault-Plugin-Developers/installScript/raw/master/install

Remove the following check in install-omv.sh:

if dpkg -l | grep -Eqw "gdm3|sddm|lxdm|xdm|lightdm|slim|wdm"; then
  echo "This system is running a desktop environment!"
  echo "This is not supported.  Exiting..."
  exit 101
fi

Run the installer with the -n switch to skip the network setup:

sudo bash install-omv.sh -n

OMV's network setup leads to non-critical errors in debian's network scripts. I did not look into that matter and simply disabled OMV's network setup since I do not need OMV to manage the Raspberry Pi's network interface and I like my start-up sequence free of error messages.

Do not configure OMV just yet.

5. Install ZFS

Run the following commands to install prerequisites for the buid process.

$ sudo apt install -y build-essential autoconf automake libtool gawk alien fakeroot dkms libblkid-dev uuid-dev libudev-dev libssl-dev zlib1g-dev libaio-dev libattr1-dev libelf-dev python3 python3-dev python3-setuptools python3-cffi libffi-dev
$ sudo apt install -y raspberrypi-kernel-headers
$ sudo apt install -y git

The procedure described here works not only on Raspberry Pi OS. If you are building on a "normal" debian system install the following kernel headers instead of raspberrypi-kernel-headers:

$ sudo apt install -y linux-headers-$(uname -r)

Now run the following commands to build ZFS. Make sure that your Raspberry Pi does not overheat.

$ git clone https://github.com/openzfs/zfs
$ cd ./zfs
$ git checkout zfs-2.1.1
$ sh autogen.sh
$ autoreconf --install --force
$ ./configure
$ make -s -j$(nproc)

To create debian packages, run:

$ pushd /usr/lib/rpm/platform
$ sudo ln -s armv7hnl-linux-gnueabihf armv7hnl-linux
$ popd
$ cd ./zfs
$ make deb

To install the debian packages, run:

$ cd ./zfs
$ sudo dpkg -i $( ls -1 *.deb | grep -v '\-devel' | grep -v '\-test' )

Test whether the ZFS module can be loaded:

$ modprobe zfs
$ lsmod | grep zfs

The output of the last command should look something like this:

zfs                  3461120  6
zunicode              331776  1 zfs
zzstd                 430080  1 zfs
zlua                  147456  1 zfs
zcommon                98304  1 zfs
znvpair                90112  2 zcommon,zfs
zavl                   16384  1 zfs
icp                   294912  1 zfs
spl                   106496  7 znvpair,zcommon,zfs,icp,zzstd,zlua,zavl

Make sure the ZFS module is loaded at boot:

$ echo "zfs" >> /etc/modules

Enable ZFS services at boot:

$ sudo systemctl enable zfs-import-cache.service zfs-import.target zfs-mount.service zfs-zed.service zfs.target

If you do not plan to install the OMV ZFS plugin, you may want to manually setup zfs-zed in /etc/zfs/zed.d/zed.rc. Otherwise you can leave this file alone for now.

6. Install the OMV ZFS plugin

Now install the OMV ZFS plugin, but not the one available by default in "Plugins" on the OMV web admin page. The original plugin comes with all sorts of dependencies we do not want and which would not work for us. Instead let's build our own version of the debian package:

$ git clone https://github.com/OpenMediaVault-Plugin-Developers/openmediavault-zfs.git
$ cd openmediavault-zfs
$ wget -O - https://github.com/hannesd/omv-zfs-ras-nas/raw/main/openmediavault-zfs-nozfsdeps.patch | git apply
$ fakeroot debian/rules clean binary

The debian package is written to ../openmediavault-zfs-nozfsdeps_<ver>_<arch>.deb.

You can upload it over the OMV web interface and install it. Make sure to isntall the ...-nozfsdeps package instead of the original.

7. Create ZFS Pools and Filesystems

Now one can create ZFS pools and filesystems through the OMV admin interface. Personally I prefer to do this on the console:

$ sudo zpool create -O acltype=posixacl -O xattr=sa -O atime=off -O dnodesize=auto -O compression=lz4 -o ashift=12 tank mirror /dev/sda /dev/sdb

• The attributes acltype and xattr allow us to use ACLs on the filesystems.
• I have read somewhere that dnodesize=auto is good for your karma, so I have added it here.
• The attribute ashift has to be set to your drive's sector size. It is the exponent in 2^12 = 4096 = 4K sector size. Adapt it to your needs.
• Set the compression to lz4 (default would be: none).
• The pool is called "tank" and is a mirror setup consisting of my two hard-drives sda and sdb.

Every pool automatically comes with a root filesystem that will be mounted at /tank. I recommend not using that and instead create individual filesystems for your needs. For example:

sudo zfs create pool/homes
sudo zfs create pool/shared

These filesystems will inherit the settings we used during pool creation but can be customized (except for the pool-specific settings).

To make sure that the pool is imported on system startup we have to make sure that a cachefile exists for our pool:

$ sudo zpool set cachefile=/etc/zfs/zpool.cache tank

This file is read by the systemd service zfs-import-cache.service which will then import the corresponding pools. Afterwards the systemd service zfs-mount.service will mount all filesystems found in the imported pools.

8. Automatic Snapshots

Warning: Enabling automatic snapshots probably prevents your drives from spinning down ever, though I have not verified this.

To enable automatic snapshots at various intervals, do the following:

$ wget -O zfs-auto-snapshot.tar.gz https://github.com/zfsonlinux/zfs-auto-snapshot/archive/upstream/1.2.4.tar.gz
$ tar -xzf zfs-auto-snapshot.tar.gz
$ cd zfs-auto-snapshot-upstream-*
$ sudo make install

Change the number of kept snapshots to match your personal preferences:

sudo sed -i 's/keep=24/keep=48/g' /etc/cron.hourly/zfs-auto-snapshot
sudo sed -i 's/keep=12/keep=3/g' /etc/cron.monthly/zfs-auto-snapshot

TODOs

• dpkg-reconfigure locales
• Use different device names:

zpool export <pool-name>`
zpool import -d /dev/disk/by-partuuid/<uuid> /dev/disk/by-partuuid/<uuid>
zpool import <pool-name>

• Import all available pools:

zpool import -a

• Get rid of unnecessary alerts on reboot

nano /etc/default/openmediavault  # Add or edit line: OMV_MONIT_DELAY_SECONDS="15" until alerts are not longer sent
omv-salt stage run prepare
omv-salt deploy run monit

• Kernel update causes problems. Complete recompile necessary. Make sure new kernel-headers are also installed and up-to-date. Problematic how we suggest to install kernel headers in the text above.
• One-liner after kernel-upgrade:

cd zfs
git clean -xdf
( sh autogen.sh && autoreconf --install --force && ./configure && make -s -j$(nproc) && make deb && dpkg -i $( ls -1 *.deb | grep -v '\-devel' | grep -v '\-test' ) ) &> logs
modprobe zfs

• Close tmuxinator session: Ctrl+b &
• List all zfs snapshots: zfs list -t snapshot