Low-Rate-TCP-DoS-Attack

Course Code: CO300

Assignment: #37

Accompanying webpage

http://sagarb-97.github.io/Low-Rate-TCP-DoS-Attack/

Overview

DoS attacks can be detected by counter-DoS mechanisms such as CouldFlare. Here, we simulate a 'Low-Rate TCP targetted DoS attack' which is harder to detect as compared to the traditional DoS attacks.

These DoS attacks make use of the TCP congestion control's retransmission timeout (RTO) functionality to stop communication between a sender and a receiver. Instead of flooding the network with traffic, as in a normal DoS attack, we 'time' these floods such that they congest the network right when the TCP sender retransmits when there is a packet loss. This will lead to the sender waiting for another RTO period, after which this flood repeats again.

Hence by carefully timing these attack bursts, we can evade counter-DoS mechanisms, and at the same hinder communication between the TCP sender and receiver.

From the reference paper:

Denial of Service (DoS) attacks consume resources in networks, server clusters, or end hosts, with the malicious objective of preventing or severely degrading service to legitimate users. Resources that are typically consumed in such attacks include network bandwidth, server or router CPU cycles, server interrupt processing capacity, and specific protocol data structures. Example DoS attacks include TCP SYN attacks that consume protocol data structures on the server operating system; ICMP directed broadcasts that direct a broadcast address to send a flood of ICMP replies to a target host thereby overwhelming it; and DNS flood attacks that use specific weaknesses in DNS protocols to generate high volumes of traffic directed at a targeted victim.

Common to the above attacks is a large number of compromised machines or agents involved in the attack and a “sledge-hammer” approach of high-rate transmission of packets towards the attacked node. While potentially quite harmful, the high-rate nature of such attacks presents a statistical anomaly to network monitors such that the attack can potentially be detected, the attacker identified, and the effects of the attack mitigated.

In this paper, we study low-rate DoS attacks, which we term “shrew attacks,” that attempt to deny bandwidth to TCP flows while sending at sufficiently low average rate to elude detection by counter-DoS mechanisms.

---

Steps to Reproduce

This project has been successfully tested and is known to be working on ns-3.27.

Clone the repository to your local machine:

git clone [email protected]:samvid25/Low-Rate-TCP-DoS-Attack.git
cd Low-Rate-TCP-DoS-Attack

Then, make the waf file executable, and build ns-3:

sudo chmod +x waf
./waf configure

Once ns-3 is built, this attack can be simulated by running tcp-low-rate.cc:

./waf --run scratch/tcp-low-rate

The PCAP files are stored in the Low-Rate-TCP-DoS-Attack/PCAPs folder for further analysis.

---

Experimentation

The different parameters that affect the attack can be varied by varying the macros in scratch/tcp-low-rate.cc.

• BULK_SEND_MAX_BYTES: The maximum bytes the legit sender transmits (in Bytes).
• MAX_SIMULATION_TIME: The duration for which the simulation runs (in Seconds).
• ATTACKER_START: The time at which the attacker node starts the UDP burst (in Seconds).
• ATTACKER_RATE: The data rate of the attacker node's UDP burst (in Kb/s).
• ON_TIME: The burst length of the attack burst (in Seconds).
• BURST_PERIOD: The burst period of the attack burst (in Seconds).
• OFF_TIME: The duration for which there is no attacker traffic (= BURST_PERIOD - ON_TIME) (in Seconds).
• SENDER_START: The time at which the legit sender starts transmitting data (in Seconds).

---

Procedure

• Initially, the following topology is set-up.

• The legitimate sender runs a TCP Bulk Send application (simulating an actual TCP transfer).
• The attacker node runs a UDP On Off application (simulating the periodic bursts).
• The receiving node just has a TCP and UDP sink running to receive the segments/datagrams.
• Once the link and node parameters are defined, and the topology is set up, the start and stop times of the applications and the frequency of the attacker bursts must be defined.
• The frequency of the attacker bursts can be varied by setting the OnTime and OffTime attributes of the OnOff Helper. The attack gives the best results at OnTime = 0.25s and OffTime = 0.75s.
• All the applications except the Bulk Send application start at time t = 0. The Bulk Send application on the sender node will start at a time equal to the OffTime of the UDP On-Off application on the attacker. This is because the UDP OnOff application is initially in the Off state. This makes sure that both the sender and attacker effectively start at the same time.
• The data rate for the attacker application must be set so that it saturates the bottleneck link in the duration that it is on (OnTime).

---

Observations

The following observations have been made for a 100 second simulation, with the following parameters:

Burst Duration (in Seconds)	Attacker's Rate (in Kb/s)
0.15	12000
0.2	12000
0.25	7000

---

References

[1] Aleksandar Kuzmanovic and Edward W. Knightly. “Low-Rate TCP-Targeted Denial of Service Attacks (The Shrew vs. the Mice and Elephants)”

[2] TCP Models in ns-3

[3] Low Rate TCP-Targeted DoS Attacks - Reproducing Network Research by Stanford