Merge branch 'release_binaries' into 'master'

release binaries added

See merge request app-frameworks/esp_hosted!66

docs/Linux_based_host/SDIO_setup.md

@@ -31,7 +31,14 @@ Please reboot Raspberry-Pi after changing this file.
 
 ### ESP32 Setup
 
-On ESP32 either use pre-provided hosted mode firmware binary or if you have source, compile the app against ESP-IDF 4.0 release. To use `make` build system, run following command in `esp/esp_driver/network_adapter` directory and navigate to `Example Configuration ->  Transport layer -> SDIO interface -> select` and exit from menuconfig.
+For pre built hosted mode firmware is present in `release` tab. To flash it on ESP32 edit <serial_port> with ESP32's serial port and run following command.
+```sh
+esptool.py -p <serial_port> -b 960000 --before default_reset --after hard_reset write_flash --flash_mode dio --flash_freq 40m --flash_size detect 0x8000 partition-table_sdio_v0.2.bin 0x1000 bootloader_sdio_v0.2.bin 0x10000 esp_hosted_firmware_sdio_v0.2.bin
+```
+
+For windows user, you can also program the binaries using ESP Flash Programming Tool.
+
+ Or if you have source, compile the app against ESP-IDF 4.0 release. To use `make` build system, run following command in `esp/esp_driver/network_adapter` directory and navigate to `Example Configuration ->  Transport layer -> SDIO interface -> select` and exit from menuconfig.
 ```
 $ make menuconfig
 ```

docs/Linux_based_host/SPI_setup.md

@@ -29,7 +29,13 @@ Please reboot Raspberry-Pi after changing this file.
 
 ### ESP32 Setup
 
-On ESP32 either use pre-provided hosted mode firmware binary or if you have source, compile the app against ESP-IDF 4.0 release. To use `make` build system, run following command in `esp/esp_driver/network_adapter` directory and navigate to `Example Configuration ->  Transport layer -> SPI interface -> select` and exit from menuconfig.
+For pre built hosted mode firmware is present in `release` tab. To flash it on ESP32 edit <serial_port> with ESP32's serial port and run following command.
+```sh
+esptool.py -p <serial_port> -b 960000 --before default_reset --after hard_reset write_flash --flash_mode dio --flash_freq 40m --flash_size detect 0x8000 partition-table_spi_v0.2.bin 0x1000 bootloader_spi_v0.2.bin 0x10000 esp_hosted_firmware_spi_v0.2.bin
+```
+For windows user, you can also program the binaries using ESP Flash Programming Tool.
+
+Or if you have source, compile the app against ESP-IDF 4.0 release. To use `make` build system, run following command in `esp/esp_driver/network_adapter` directory and navigate to `Example Configuration ->  Transport layer -> SPI interface -> select` and exit from menuconfig.
 ```
 $ make menuconfig
 ```

docs/Linux_based_host/UART_setup.md

@@ -41,7 +41,13 @@ dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=5c2c80d1-02 rootfstype=ext4 elev
 
 ### ESP32 Setup
 
-On ESP32 either use pre-provided hosted mode firmware binary or if you have source, compile the app against ESP-IDF 4.0 release. To use `make` build system, run following command in `esp/esp_driver/network_adapter` directory navigate to `Component config ->  Bluetooth -> Bluetooth controller -> HCI mode -> UART(H4) -> select` also to set baud rate, `Component config ->  Bluetooth -> Bluetooth controller ->  HCI UART(H4) Options -> UART Baudrate for HCI -> <set baudrate> -> Ok` and exit from menuconfig.
+For pre built hosted mode firmware is present in `release` tab. To flash it on ESP32 edit <serial_port> with ESP32's serial port and run following command.
+```sh
+esptool.py -p <serial_port> -b 960000 --before default_reset --after hard_reset write_flash --flash_mode dio --flash_freq 40m --flash_size detect 0x8000 partition-table_sdio_uart_v0.2.bin 0x1000 bootloader_sdio_uart_v0.2.bin 0x10000 esp_hosted_firmware_sdio_uart_v0.2.bin
+```
+For windows user, you can also program the binaries using ESP Flash Programming Tool.
+
+Or if you have source, compile the app against ESP-IDF 4.0 release. To use `make` build system, run following command in `esp/esp_driver/network_adapter` directory navigate to `Component config ->  Bluetooth -> Bluetooth controller -> HCI mode -> UART(H4) -> select` also to set baud rate, `Component config ->  Bluetooth -> Bluetooth controller ->  HCI UART(H4) Options -> UART Baudrate for HCI -> <set baudrate> -> Ok` and exit from menuconfig.
 ```
 $ make menuconfig
 ```

docs/MCU_based_host/Setup.md

@@ -44,6 +44,14 @@ The control path between host and ESP32 is based on `protobuf`. For that `protoc
 ```
 $ git mv components/protocomm/src/common/protocomm_priv.h components/protocomm/include/common/
 ```
+For pre built hosted mode firmware is present in `release` tab. To flash it on ESP32 edit <serial_port> with ESP32's serial port and run following command.
+```sh
+esptool.py -p <serial_port> -b 960000 --before default_reset --after hard_reset write_flash --flash_mode dio --flash_freq 40m --flash_size detect 0x8000 partition-table_spi_v0.2.bin 0x1000 bootloader_spi_v0.2.bin 0x10000 esp_hosted_firmware_spi_v0.2.bin
+```
+For windows user, you can also program the binaries using ESP Flash Programming Tool.
+
+Or if you have source, follow below procedure.
+
 Currently ESP32 and STM32 communicates over SPI transport. To use `make` build system, run following command in `esp/esp_driver/network_adapter` directory and navigate to `Example Configuration ->  Transport layer -> SPI interface -> select` and exit from menuconfig.
 ```
 $ make menuconfig

esp/esp_driver/network_adapter/CMakeLists.txt

@@ -2,5 +2,10 @@
 # in this exact order for cmake to work correctly
 cmake_minimum_required(VERSION 3.5)
 
+set(PROJECT_VER "0.2")
+message(*************************************************************************************)
+message("                    Building ESP-Hosted Firmware version :: ${PROJECT_VER}             ")
+message(*************************************************************************************)
+
 include($ENV{IDF_PATH}/tools/cmake/project.cmake)
 project(network_adapter)

esp/esp_driver/network_adapter/Makefile

@@ -3,7 +3,13 @@
 # project subdirectory.
 #
 
-PROJECT_NAME := network_adapter
+PROJECT_VER := 0.2
+$(info *********************************************************************************)
+$(info *              Building ESP-Hosted firmware version :: $(PROJECT_VER)                )
+$(info *********************************************************************************)
+
+PROJECT_NAME := network_adapter_$(PROJECT_VER)
+CPPFLAGS += -DPROJECT_VER=$(PROJECT_VER)
+
 EXTRA_COMPONENT_DIRS := $(realpath ../../../common)
 include $(IDF_PATH)/make/project.mk
-

esp/esp_driver/network_adapter/main/CMakeLists.txt

@@ -7,4 +7,7 @@ else(CONFIG_ESP_SPI_HOST_INTERFACE)
     list(APPEND COMPONENT_SRCS spi_slave_api.c)
 endif()
 
+
 register_component()
+set(PROJECT_VER "-DPROJECT_VER=0.2")
+target_compile_definitions(${COMPONENT_LIB} PRIVATE ${PROJECT_VER})

esp/esp_driver/network_adapter/main/app_main.c

@@ -99,6 +99,18 @@ static inline int min(int x, int y) {
     return (x < y) ? x : y;
 }
 
+static void print_firmware_version()
+{
+	ESP_LOGI(TAG, "*********************************************************************");
+	ESP_LOGI(TAG, "                ESP-Hosted Firmware version :: %.1f                        ", PROJECT_VER);
+#if CONFIG_ESP_SPI_HOST_INTERFACE
+	ESP_LOGI(TAG, "                Supported Transport :: SPI                           ");
+#else
+	ESP_LOGI(TAG, "                Supported Transport :: SDIO                          ");
+#endif
+	ESP_LOGI(TAG, "*********************************************************************");
+}
+
 static uint8_t get_capabilities()
 {
 	uint8_t cap = 0;
@@ -613,6 +625,7 @@ void app_main()
 {
 	esp_err_t ret;
 	uint8_t capa = 0;
+	print_firmware_version();
 
 	capa = get_capabilities();